byrd Posted April 20, 2005 Share Posted April 20, 2005 Hi guys! I'm new to the forum. Can anyone help me with my 95 SC300 powered windows problem? The pass side controller works fine, but the driver side is not working at all i can't roll up or down the windows at all! either driver or passenger side, the door lock switch is working fine, I also did check the motor for the driver side windows it's OK :cries: I have done a search but did not find anything as of yet.. Quote Link to comment Share on other sites More sharing options...
JDOwen2 Posted April 21, 2005 Share Posted April 21, 2005 I'd guess your switch is toast or a wire broke off. Quote Link to comment Share on other sites More sharing options...
jim_darci Posted April 24, 2005 Share Posted April 24, 2005 I'm having the same problem. I just bought to new switches off of ebay. I will let you know when I receive them if this is a possible fix. Quote Link to comment Share on other sites More sharing options...
karlasetser Posted April 24, 2005 Share Posted April 24, 2005 Hi guys! I'm new to the forum. Can anyone help me with my 95 SC300 powered windows problem? The pass side controller works fine, but the driver side is not working at all i can't roll up or down the windows at all! either driver or passenger side, the door lock switch is working fine, I also did check the motor for the driver side windows it's OK :cries: I have done a search but did not find anything as of yet.. ← My driver window on 95 sc300 just went out too..guess it's an age thing! Quote Link to comment Share on other sites More sharing options...
jim_darci Posted April 29, 2005 Share Posted April 29, 2005 Just got my new switch and it didn't help. On to the next step. Maybe the motor or possibly a wire issue. I may just end up taking it to the dealer. I am in Florida and it is too stinkin' hot to be driving around with only the sunroof and one window working. Quote Link to comment Share on other sites More sharing options...
LLS Posted April 29, 2005 Share Posted April 29, 2005 Most of the time it is the switch, however i have seen the wire age inside the gromet from where the door is repeatedly opened and closed. Quote Link to comment Share on other sites More sharing options...
rayikone Posted April 29, 2005 Share Posted April 29, 2005 I had the same problem. First I bought a brand new switch, no help. Then I got the wiring diagram and shot the wires. Found a bad ground, so I jumped it and everything worked fine. That worked for about six months then the window failed again. I wound up taking it to the dealer and they replaced the driver's side harness. Quote Link to comment Share on other sites More sharing options...
taadow77 Posted June 7, 2005 Share Posted June 7, 2005 Hey guys - I just fixed this problem on my 92 sc. It turned out to be the window regulator and not the motor. Not that big of deal as it turns out. Good luck! Quote Link to comment Share on other sites More sharing options...
LEXIE Posted June 7, 2005 Share Posted June 7, 2005 taadow77-- Lexie here. I am repairing my passenger side power window. I have a regulator on order and already removed the door panel in prep of removing the existing regulator. My questions: What steps did you go thru to remove the old unit. The motor/regulator unit seems to be in a tight spot. Was there a problem in unhooking/re-hooking the electrical connection. Was the window in the down position when you installed the new regulator. Any and all comments would be most appreciated. I have a '93 SC400. Thx, L Quote Link to comment Share on other sites More sharing options...
.jpg.00b008f265e99d7d6120b5e549b3fd10.thumb.jpg.19472090d3f0c8af2c0ed917c349221d.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.