0260n5.7

Last pic. A close up. I later changed the driving light bulb to match the HID color.

Here is a pic of the HIDs in action compared to my OEM Tundra lights

Here are some pics. It took alot of detail but not necessarily difficult work to get it right. I did have to separate the connector from the wires on the HID kit, drill a hole in the cover of the OEM light housing cover, run the HID kit wires through the hole (the kit comes with a grommet that helped out a bunch), reconnect the wires to the connector on the HID kit and then install everything nicely.

I'll post pics tomorrow (they're on my work computer) of a total transformation to LED interior and exterior bulbs. Until then... MAC

All, FWIW if any of you are interested, I'll post DIY pics of the dvd speed sensor and hand brake override if you so desire. It allows PASSENGER viewing of dvd and inputting of phone numbers while in motion. I don't have NAV so i can't comment on whether or not it'll work with NAV. Let me know if you would like the DIY guide. MAC

All, it CAN b done. I did it with complete success! i even put HIDs in the fogs MAC

If you are referring to the embelms on the outside of the car, you don't need to remove the interior panel. The emblems are attached via tape and, after being heated with, say a blow drier, can be removed by using dental floss. HTH MAC

Andrew, No experience with the SC yet. As far as the bulbs are concerned, depending on which bulbs you change, it could take a couple hours. I mean if you change the reverse light and door light bulbs, you'll have to contend with the panels etc. Not a tough job at all though. HTH MAC

The US GX470 has an H11 bulb in the low beam. It is different from an H1 bulb. MAC

The H11 HID kit is still in production. I'll keep you posted of any updates I hear about. MAC

As all additional monitrs are individually controlled, her is a pic of two monitrors and the main system in action. MAC

Thanks for the props. I haven't installed the S/C or the exhaust. According to my source "they" are still working out some minor details. Guam doesn't get the NAV option. The lights were acquired through a source in Central America. The housings fit perfectly but the alignment of the bulb receptacle to the housing is not the same. I had to do a little modification to the housing and relocate the contacts to get it to work. If you are at least a little electronically inclined, it is a 2 on a scale of 1 - 10, 10 being hardest. Here are some recent pics of the latest mods...enjoy MAC

RDH1210, Very nice wheel/tire combo. What offset did you get and who makes that wheel? No rubbing on the inside fender at full turn? Here is a shot of the latest mod. B) MAC

washcorp, power, power, and more power. I know its not really needed on an SUV, but it would be cool to have just as a project since all the parts will be bolt on. MAC

I accessed it from the rear from under the vehicle. HTH MAC

Al, Look below @ my other threads. That'll give you some ideas i.e. wheels, lighting, rear spoiler, emblems, etc. MAC

The photos everyone has come up with are speculative at best. MAC

tsai, Both are pricey but worth the $ IMO. Both are also kinda hard to get. Check with www.wheelexperts.com as for Peter. Tell him I sent ya. MAC

295/45x20 Pirelli Scorpion Zeros

HRE full polish 648Rs

Here they are. the much anticipated wheels. MAC

another MAC

another MAC

FINALLY! Here are some pics. The anticipation is finally over! 20x9.5 HRE 648R full polish with 295/45x20 Pirelli Scorpion Zeros! I'll post better pics later. Just thought I'd share these for now. The decision was very tough but I couldn't be happier with the 20s. My GF loves them. I have to say they are perfect. Wide to the flared wheel well and enough sidewall to keep the SUV look and feel and to protect from curb rash. Saturday I will install the TRD performance air filter. MAC

Checked with my TRD connect today and he said they are not ready yet. If you have any updated info please advise. btw, I just got the HREs on today. MAC