
Satz
Regular Member-
Content Count
56 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout Satz
-
Rank
Club Member
Profile Information
-
Lexus Model
RX350
-
Has Anyone Done Suspension Mods On The Rx?
Satz replied to Satz's topic in 04 - 09 Lexus RX330 / RX350 / RX400h
hi there I guess my aim is not to get a rigid or bumpy ride, but perhaps lower the car by approx 10-20mm and mainly to reduce its roll and make it a little more responsive out of corners. I used to have a Mazda CX7 which, for all its other faults!, handled much better than my RX This was the sort of thing I was thinking of: http://www.andysautosport.com/lexus/2004_9999_rx/suspension/lowering_springs/eibach/ Satz -
hi all Am thinking of fitting hubcentric wheel spacers to my 07 RX350, mainly to widen the stance of the wheels so they're closer to the bodywork. I hate that narrow-tracked look, esp of the rear wheels. Can't afford to change the stock wheels so was thinking of using custom hubcentric wheels spacers approx 25mm wide. Anyone used them on their RX? cheers S
-
Hi All I have an 07 RX 350 AWD and I feel the suspension is, by design, a little too soft for my liking. The only aftermarket solution I can find is the one made by Eibach. Not sure if I'm allowed to post a link or not. Has anyone used this, or any other kit? How did you find the handling and ride after? Did it improve/ get too harsh or choppy? cheers Satz
-
Rx350 Sluggish/slow Compared To Highlander/kluger V6 Awd
Satz replied to Satz's topic in 04 - 09 Lexus RX330 / RX350 / RX400h
one of the more annoying characteristics I've foudn with my car is its non-linear response to the pressing of the throttle pedal. In fact, non just non-linear, but non-predictable. Sometimes nothing happens with the initial half travel of the pedal, which can get dangerous when overtaking or crossing intersections. Not much response until you floor the pedal, which is not how it was on the Highlander AWD. The Highlander responded well to light pressing of the accelerator. -
My Mechanic Doesn't Want Me To Buy A Used Rx350
Satz replied to Bopper's topic in 04 - 09 Lexus RX330 / RX350 / RX400h
I actually don't think the technology in the 07 - 08 RX is actually very complicated. 5 speed auto (rather clunky) Toyota electronics, HVAC, drivetrain, etc My 07 RX 350's engine seems pretty weak, and non-linear in response... -
hi all have had my 2007 RX 350 AWD for about a year now. Recently I had a rental 2010 Toyota Kluger (Highlander) AWD automatic and found that it was much quicker in acceleration, as well as in overtaking! I can't understand why as the specs show that the Highlander's body weight is higher, and it uses the same engine and transmission. My RX350 feels like a slug, especially when the AC is on. The Highlander felt more responsive, even with the AC on. Has anyone else compared the two? Satz
-
Annoying Buzzing Noise - Can Anyone Helo?
Satz replied to VickiK3275's topic in 04 - 09 Lexus RX330 / RX350 / RX400h
Try to tighten the screws and fasteners that hold the door trims (front and back doors) Also check that the noise isn't coming from something tiny lying in the door pockets. And check that the trim piece behind the seat belt is securely fastened (I think it's held in place by the door frame rubber seals) Let us know how you go -
How To Change Rear Wiper Blade?
Satz replied to Satz's topic in 04 - 09 Lexus RX330 / RX350 / RX400h
thanks all I managed to just get the oem rubber part from Toyota, not the whole arm. This rubber part did come with 2x metal strips which are installed with the rubber. IIRC I pulled the rubber away in the middle from the plastic arm and replaced it in the same way Satz -
Can I Claybar A 'protected' Paintwork?
Satz replied to Satz's topic in Lexus Detailing and Car Care Forum
Hi The protection on my car must be the spray-on type. I fully agree with you that it's a waste of money, and never got it on any of my new cars (only on this used one)! The surface feels pretty smooth, but just not as 'expensive' looking as I'd expect Lexus paint to look. I might take the clay to a section of it to test. And then polish. I've used Zaino polish before, and now switched to Meguiars Tech Wax 2.0 Also thinking of getting a random-orbital sander/polisher to do the buffing as my old shoulders are getting too sore :) -
Hi all Bought a used 2007 rx 350 which has the paint protection on there from original owner. I don't feel the paint is as deep looking as it could be after washing and polishing. would it help to run claybar over it, or will it make no difference to a paint-protected paint? Or worse still, could it make a mess od the protection and hence the finish? i had good results with clay on my previous car... Thank you P.s. Couldnt get much advice from the paint protection company!
-
Hi CD many thanks for all that info. It's great to hear from someone who has also done the hard-yards! The LED bulbs on the link you provided sound great. So do they end up as a similar colour to the stock low-beam HID? And also, do you feel they produce the same amount of visible light output as the original filament bulb? kind regards Satz
-
That noise sounds like a bearing. Does it happen more when you turn in a particular direction? If so, the noisy bearing is the one on the side of the car not under load at the time (usually!) The the warranty should cover it, unless it was damaged by running into a kerb or something...