jaz Posted October 25, 2004 Posted October 25, 2004 I want to do a tune up on my lx450. It looks like it should not be a problem but just wanted to get some pointers. When I time it is there anything I should know, such as vacum hoses and such. I will be replacing spark plugs, distributor cap & Rotor, I am not sure about the wires though. I have 99,000 miles on it now. Also I put on a K&M air filter and it was smaller than the regular air filter, is this okay? Thanks for any input.
Rookie Posted October 25, 2004 Posted October 25, 2004 When I time it is there anything I should know, such as vacum hoses and such. ← jaz- I don't quite understand this first question. If you're talking about engine timing, I'm not sure what the connection with vacuum hoses you're asking about. Have you purchased an FSM to know how to short out the ECU when checking/setting timing? Please clarify. Have you tested the resistance on the spark plug wires? If any are above 25kohm, then toyota says to replace. With your mileage, you're probably not to far from going ahead and replacing, if not now then at the next tune-up. Don't know much about the K&N filters. Most discussion I've seen about them recommend staying with OEM. Rookie
jaz Posted October 25, 2004 Author Posted October 25, 2004 I want to do a tune up on my lx450. It looks like it should not be a problem but just wanted to get some pointers. When I time it is there anything I should know, such as vacum hoses and such. I will be replacing spark plugs, distributor cap & Rotor, I am not sure about the wires though. I have 99,000 miles on it now. Also I put on a K&M air filter and it was smaller than the regular air filter, is this okay? Thanks for any input. ←
jaz Posted October 25, 2004 Author Posted October 25, 2004 When I time it is there anything I should know, such as vacum hoses and such. ← jaz- I don't quite understand this first question. If you're talking about engine timing, I'm not sure what the connection with vacuum hoses you're asking about. Have you purchased an FSM to know how to short out the ECU when checking/setting timing? Please clarify. Have you tested the resistance on the spark plug wires? If any are above 25kohm, then toyota says to replace. With your mileage, you're probably not to far from going ahead and replacing, if not now then at the next tune-up. Don't know much about the K&N filters. Most discussion I've seen about them recommend staying with OEM. Rookie- On some other vehicles A while back someone had told me I had to disconnect a vacuum hose to get the correct timing reading. I have not yet purchased the FSM but I guess I really need to. How do I test the resisitance on the spark plugs? Rookie ←
dougjohn2 Posted October 25, 2004 Posted October 25, 2004 replace the spark plug wires with OEM wires (always use OEM sparkplugs and wires with the 450 for best results). I personally stick with OEM air filter myself.
Rookie Posted October 25, 2004 Posted October 25, 2004 On some other vehicles A while back someone had told me I had to disconnect a vacuum hose to get the correct timing reading. I have not yet purchased the FSM but I guess I really need to. How do I test the resisitance on the spark plugs? Rookie ← The procedure for checking the timing requires jumping the ECU. You need the FSM or Chiltons to know what terminals in the ECU need to be jumped. You can do this with a paperclip. There is no mention of removing any vacuum hoses. You check the spark plug resistance by using an ohm meter. Unplug the wires at the distributor cap and plugs ends and check the resistance across the ends. The resistance will increase as you go from number 1 to number 6 (as the wire lengths increase). As mentioned above, if any are over 25 kiloohms they should be replaced. Chiltons recommends any over 15 Kohms as cause for replacement. My number 6 was 18. I'm still running it. Rookie
jaz Posted October 26, 2004 Author Posted October 26, 2004 On some other vehicles A while back someone had told me I had to disconnect a vacuum hose to get the correct timing reading. I have not yet purchased the FSM but I guess I really need to. How do I test the resisitance on the spark plugs? Rookie ← The procedure for checking the timing requires jumping the ECU. You need the FSM or Chiltons to know what terminals in the ECU need to be jumped. You can do this with a paperclip. There is no mention of removing any vacuum hoses. You check the spark plug resistance by using an ohm meter. Unplug the wires at the distributor cap and plugs ends and check the resistance across the ends. The resistance will increase as you go from number 1 to number 6 (as the wire lengths increase). As mentioned above, if any are over 25 kiloohms they should be replaced. Chiltons recommends any over 15 Kohms as cause for replacement. My number 6 was 18. I'm still running it. Rookie ←
jaz Posted October 26, 2004 Author Posted October 26, 2004 On some other vehicles A while back someone had told me I had to disconnect a vacuum hose to get the correct timing reading. I have not yet purchased the FSM but I guess I really need to. How do I test the resisitance on the spark plugs? Rookie ← The procedure for checking the timing requires jumping the ECU. You need the FSM or Chiltons to know what terminals in the ECU need to be jumped. You can do this with a paperclip. There is no mention of removing any vacuum hoses. You check the spark plug resistance by using an ohm meter. Unplug the wires at the distributor cap and plugs ends and check the resistance across the ends. The resistance will increase as you go from number 1 to number 6 (as the wire lengths increase). As mentioned above, if any are over 25 kiloohms they should be replaced. Chiltons recommends any over 15 Kohms as cause for replacement. My number 6 was 18. I'm still running it. Thanks for the info. Rookie ← ←
Rookie Posted October 26, 2004 Posted October 26, 2004 Thanks for the info.Rookie ← Whoops... it appears you're having a little trouble with the reply function. BTW, You're jaz, I'm Rookie. I let it slide the first time :D . Rookie
EnDLesS Posted October 26, 2004 Posted October 26, 2004 My 97 LX450 179K Tune Up~ Just basic maintenance/ Routine, - Spark Plug Wire - Bosch Platinum +4 - Drive/ Serpentine (3) Belts - JAOS air Filtercharged - 7/8 Quarts Mobil 1 Synthetic 10W-30 & 15W-50 / Genuine Toyota oil filter. - ATF Synthetic Fluids - Castrol Synthetic 75w-90 Gear oil - Fuel Filter - Car Battery check up - Toyota AntiFreeze -red ( with 2 bottles redline waterwetter mixed) 50/50 drinking water ~am i crazy heh? but yeah to prevent rust. :D - Reflush Brake Fluids I guess thats about most i cant think of any more than the list.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now