EMTtech

it can be done, yes. make sure you have the proper tools - the 1992 and 1993 are the only two years that have the 3VZ-FE engine, so yes. stick with 92 and 93 cars

shouldnt be too hard, theres plenty around with blown motors

-Erik

its possible its just a piston ring, but the way it sounds with clanging as you described. yes. it is nessesary to replace the engine

if you have a good helper whos done it before at your side with a new 1MZ-FE in hand and a proper set of tools you can get it done on the cheap.

there are 1mz supercharger kits out there made by TRD, but they are for the post 1996 VVT engines. this can be made to fit, and on stock internals, and ECU you can push about 4-6PSI, with stock internals, dont go above PSI on a 1MZ for longevity sake, but if you beef it up and get a stand alone fuel management and ECU, that supercharger can easily push 12PSI with aftermarket pullys

in short, if you want a fast car, dont use an ES as a starting block

next time it rains, put a bottle of isopropylene in the tank and see if that fixes the issue. last time i had this issue I did that and it fixed the issue.

has nobody else run into this problem before? I fixed all but the gas needle, but I still need to know how to get to the back lighting

-Erik

Here is the link to the backlighting DIY write-up.

As far as the speedo needle reading too low is concerned - you can try pulling the needle off again and repositioning it so that it is in line with the "0" MPH mark when the car is in PARK and the engine is running. If it is still reading low, you might have to adjust the balance of the needle slightly so that it sits at the right point on the gauge. If after the needle mod is done there is a bit more weight at the tip end of the needle than there is at the base end, you can add some weight to the base end to better balance the needle. To do this, melt a very tiny bit of solder (and I mean TINY - solder is heavy) onto the metal counter-weight which is on the underside of the needle, right at the base. Then test the needle to see how it is now positioned on the gauge. If it is still not reading correctly, add a tiny bit more and retest again. Do this as many times at it takes to get the needle to rest at the right spot on the gauge.

Hope this helps.

when I put in my SMDs, I used one 660ohm resistor in the back part of the needle because I used heavy wire, it seems to be fairly well balanced. and if my car is a stick, should I just leave it in Neutral instead of park? as far as the speedo goes, it's only about 3MPH off according to my D3's GPS so Im not worried about that. the gas gauge I hope I can right though. Thanks for the link the the backlighting thread again, I had lost track of it somehow

indeed, it helps

Thank you!

has nobody else run into this problem before? I fixed all but the gas needle, but I still need to know how to get to the back lighting

-Erik

is this oil recommended? 0-20w, hell no. Use your SAE 5-w30, I am not being a jerk to you burnickas or trying to ruin your opinion. But you need to be running the oil that is recommended in the owners manual. They know what is right for your engine, and if you fail to listen, you probably arent going to be to happy when your driving to work for your boss is p'd off and you are late becuase your motor blew up from overheating and oil consumption. Change your 5w30 every 3-5 thousand miles. I RECOMMEND IT!

You crack me up......Gee, my oil tests are better then the 5w-30 and Lexus does not use 5w-30 anymore. Oil in the manual is a JOKE. They are behind the times. Example, I need an SL rated oil...give me a break. Plus you can use ow-20 in place of a 5w-20/30 and be 100% fine. Hell, I use 5w-30 in a diesel engine that calls for 15w-40; which is too thick.

Again you and others in the forum/thread THINK 3 to 5 K miles gets you something. Prove it with showing me the data? You nor anyone on this thread can since you are all guessing; that is a fact here. I know how my engine is running and oil duration etc is a benefits. Which you all are lacking.....Again fact and I have stated that many times. If you are not testing you are guessing on oil performance.

Oil consumption has nothing to do with oil weight! See, you need to stop posting on oils since you are posting BS. Fact here

well you dont have to be a smarty pants, oil is cheap, fun to change, and easy to deal with. The thinner stuff gets hot, and will boil if the motor heats up enough. trust me I know man. Stop tellinf me I am posting Bull*BLEEP*. I can post what I want, try stopping me. I am a member and so are you. We are aarguing over oil, its 2 buchs or less a quart, big deal. Did you make the engine, noo toyota did. Who puts 0w-30 in their motor. ONLY YOU DO. YOU ARE THE FIRST PERSON TO USE THAT CRAP THAT I HAVE EVER SEEN. that stuff would suck. do not put the bozo clowns recommended oil in your car. he wants to see you come here *BLEEP*ed off. Until I find this oil thing works, i am going to be arguing here. If it works, I will beg for some forgiveness.

:D sorry if i am sounding like a moron

you should listen to mburnickas, he knows more about oil, gas, additives, and the 1MZ (amongst other things) than I or you could ever hope of knowing. for the record, I run GC 0w30 Euro oil now with Lc20 (thanks to mburnickas) and so does just about everyone I know in every kind of car. if your car is boiling 20 or 30w oil and it's a toyota/lexus your engine has problems. I drive my ES harder than you could possibly imagine when I drive it, and my engine is sludge free and clean as a whistle (I also have pics to prove that) and my car has done 131K miles. I run 0W30 GC in all my cars, and swap oil every 5000-7500 miles with my mobil1 filter, once I switch to the Amsoil filter, it's going to 10K miles. please, please listen to mburnickas who is only trying to give this guy some proper advice.

sorry if that was at all harsh, I'm just giving my $.02

-Erik

man just replace the factory ones if you have to, speeding tickets suck, but for the back lights, there should be two screws that will remove the assembly. they are located above the glass display cover for the speedometer, ask a mechanic at your local dealership, I saw one using blue light condoms tochange the lighting color.

the needle is not the problem. speeding tickets can be avoided with common sense, attentiveness, and a Valentine ONE. the two screws that I found are only to remove the smoked plastic shield, where should I be looking for the two that allow me to remove the cluster? I have new LEDs to replace the burnt out ones but need to remove the cluster to finish the job

-Erik

I am installing <RED tipped needles and my speedo is now reading about 5MPH slow. it starts 5 below 0 and it doesn't fix itself higher up in the range. they look great but thats kind of an annoyance. is there any way to fix that? also how do I remove the cluster assembly to replace the back lighting? its not apparent, and its extremely hard to get to the wires that connect the cluster to. they aren't dragging on the plastic thats one of the things I thought it might be but that makes no sense

any help appreceated

Thanks,

-Erik

the 3MZ was an interference engine but was relatively un-changed in its whole lifespan even before it was bored out in 1MZ-FE (3.0) form. don't hold me to it, but I'm nearly positive that all the 1MZ engines were not 'interference engines'. still make sure the belt has been changed because it's not fun to be stranded with one of those. not sure though since the 3MZ is essentially a bored out 1MZ and it changes from isn't to is an interference engine.

-Erik

I finally got around to changing the gasket, and wow. that was not as hard as I was anticipating :D

I attached a pic of the open cover (I assume this looks A-OK) I have a link to the rest of the pics too (sorry for the random ones, they were trying to show hidden nuts)

http://picasaweb.google.com/EMTtech/ES300VCGasketReplacement

-Erik

are you sure you re-attached the harness to the trip buttons (i attached a pic of the harness you need to have attached, it's the one at the bottom thats hardly visible.) It's not related to the gas gauge though, you can have an accurate gas gauge and the trip buttons un-plugged.

hope that helps, let me know if you have any other questions

-Erik

oh, I didn't realize that LC20 was made by the same company as FP60. Ive been using that for ages, awesome! next time I get a gallon of FP60, Ill get myself a jug of LC20 too, ill be putting on the new VC gasket in a day or two. Ill post up some pics of my adventure if people would like,

Thanks again,

-Erik

wow, $980 :o ... I think ill stick to water!

as for the $9 seals? not sure what those are referring to...

also any good place to get my grubby little mitts on some LC20? or the Amsoil filters?

Thanks again for your help!

-Erik

I was joking. Spend the $6 and get Amsoil Power Foam. 10000X better then water for intake cleaning. The VC seals are about $9 from OEM.

sorry.

gotcha about the actual price, haha

where to get the amsoil filter, or the LC20 though?

also are the VC seals different than the gasket?

-Erik

wow, $980 :o ... I think ill stick to water!

as for the $9 seals? not sure what those are referring to...

also any good place to get my grubby little mitts on some LC20? or the Amsoil filters?

Thanks again for your help!

-Erik

wow, thats a lot of CCa's i've got a Lithium battery in my MR2 and that only puts out 550 (granted it's tiney and only weighs 6lbs) but yeah, I wouldnt worry about it, it's just one of those toyota things. if it's annoying, just replace all your interior lights to Regulated LEDs, and headlights to HID and you have done it! no more flickering! :P

ABS uses a large amount of power so that explains that, but before I had HIDs in my toyota's (MR2 and ES) they both dimmed for a sec when I applied the breaks at any force. this doesn't necessarily mean your alternator is bad, but it might be. I wouldnt worry about it unless you get some other signs of a dying alternator such as slower cranking speed, etc.

-Erik

I have a 98 ES and my short comments are:

You have a valve cover gasket leak and a high mileage oil most time contains seal swells. Toyota oil is remarketed Mobil. They do not really do anything to the seal, just make it larger to keep things from leaking. In my eyes they are not needed. Heck, I use Amsoil 0w-20 in a car with over 120,000 miles and no leaks. My car LOVES Amsoil and Lc20. I tried other oils in the past and other oil products and so far, I recommend them to all. Even if you do not use Amsoil use the LC20. It is a great product that I am very glad was told to me by one of my oil testing houses.

I also do extended oil changes, between 10 to over 12,000 miles, since they work if you know how to construct a baseline and then go from there.

The sludge issue in autos is most times due to items not integral to the car. Use a good oil and you are golden for well over 7,500 miles. I say that based on my past years of UOA's.

Mobil is a good filter. If you want the best, yes the best get the new Amsoil Eao filter. It is unreal on how good it is. No BS, it is the best to date and should be for the price. Heck, you can go well over 1 year on these filters and be fine.

No worries on the oil coming out of VC when removed. You will get some but not a lot. Most will be in the pan and not by the valves.

For cleaning (engine, rings, seals) and maintaining them, I like Lc20 from lube control. It works, no BS from owners (unlike some products), been around for a long time; approx 70+ years, simple to use, makes the oil even better. It WILL reduce wear a huge amount (mine at least 50%), keep TBN's high/stable (TAN low), and clean all internals. It was amazing what it did to my engines. Works slow and very well.

Ps. Since some people have a thing for the pimped seafoam I cleaned my wifes car (intake). I tried seafoam via brake booster hose; did crap. Did a spray bottle with water; WAY better but Amsoil Power Foam worked the best. The intake is nice and clean along with the IAC. Do not trust me folks, try the 3 products and look at the results. I am still amazed on how good the stuff works. I used to like seafoam but that is crap now. Do not waste your money here. I know my ES needs another cleaning since it is dirty. I thought water was great or better then seafoam and it is; but, not power foam. So simple, no hoses to remove, no chance of hyro-locking car and cleans more then seafoam could ever do.

wow, that was incredibly informative! Ill have to get my hands on the Amsoil filters. if I run my 0W30 GC through that thats fine right? how long should my oil change intervals be on that combo? as for the Lc20 from Lube Control, what is it and what does it do (forgive my noobness). and as for cleaning the motor... I run the engine, and spray water in the intake or what? I picked up a VC gasket from Mr. T. and It's just the rubber gasket that goes between the cover and the head right?

thanks much!

-Erik

Yeah, I'm thinkin you might wanna get off the full synthetics, and maybe switch to high mileage blend. Todays high mileage motor oils are designed to keep seals conditioned and clean a little better. Just a thought. I'm an Amsoil user. But to each thier own.

Mobil filters are fine. It's not like your running extended rev limits and need to raise the oil flow rate or anything. Changing them regularly is the key.

If I'm not mistaken, oil capacity is 4.7 qts. Ask Mburnackis while your talking to him as he owns one and probably will have the exact figure if not just back up what I think it is.

Oh, and you just have the one PCV valve.

To take out the rear valve cover you have to remove the air cleaner housing, throttle body and also the maf and intake pipe.

do I need to worry about oil coming out of the valve cover when the car is off? as I remember it there is only oil pumping through the valve cover when the engine is on and producing oil pressure...

Your welcome, I hope it works for you as it did for me. and thanks... I like cars.... a lot, :D

-Erik

Yeah, I can't remember where the needle was so I can't get it to work at all. I keep putting gas in my car and the needle won't move. I didn't even repair the gas gauge needle so I don't know why its doing this.

I guess the thing I would try next, fill er' up to the top, un-plug the cluster from all electronics, then put the gauge back up to where it is on the Full mark, then plug it back in to the car and cross your fingers. even if you un-plug it then plug it back in it can do this. it's the only gauge that does the manual reset thing for some reason but as I remember it has to be fairly exact

other than that, I have no idea what you should do

-Erik

I suggest cleaning your MAF or Mass Airflow Sensor, there are tutorials on the internet if you want to do it yourself, all it takes is a screw driver, a can of carb cleaner, and about 15 min for a complete novice. that idle thing happened to my MR2, cleaned the MAF, and it did wonders. if it keeps doing it after that. get the code from your computer, and see what it says and proceed from there. if the CEL is flashing thats not good, but it CAN be caused by a dirty MAF

-Erik

(anyone, correct me if I'm wrong, this might be a whole different game than my MR2)

Your welcome, I hope it works for you as it did for me. and thanks... I like cars.... a lot, :D

-Erik

when you re-install the cluster, you must manually put the gas gauge back as close as you can to where it was, I don't know why but when I took my cluster out to change out the back light, i had to do this to fix it

I'm aware of the sludge issues with those motors, that's why I suggested just making sure you have a good maintenance schedule. Mburnickas here on the forum would be good to talk to as I think he has about the same year car and model you do, and he takes pretty good care of it. Maybe find out from him what he's doing to stop the sludge issue.

The PCV valve is an easy change also. So sure. if your there, why not. It's a 5 dollar part!

I'll have to message him and get some pointers. as for the PCV, is there one per valve cover, or just one for the whole thing? I use Castrol Syntec 0W30 European Formula oil in the rest of my cars and love it, is there any reason that shouldn't be a good choice for this older car? also I usually use mobile 1 filters, is that OK?

also If you know; which I cant imagine you would, do you know how many quarts of oil go in the motor when I put it in? My car didn't come with an owner's manual

Thanks again,

-Erik

well Ive done quite a bit with my MR2s 1zz-fed but have never done anything with my 3vz as its a new addition to my car family. I'm glad to hear you dont think its nessesary until it breaks. I was simply curious, and only intend on changing the valve cover gasket and oil this weekend. What about the PCV valves on the notorious sludge monster 3vz?