theazz

This should not be a problem. Does the bolt screw in easily without the caliper? If not I would spry some wd-40 in the hole and try again. If still hard to turn it could be cross threaded. Also while the caliper is off try the other bolts in their respective holes. Regarding lining the holes with the caliper it should fit perfect since it came off. When I did mine I kept the first bolt loose until I started the other bolt. I've done about 3 sets of these on different SC's and never found the bolts to be a problem. Good Luck

the azz

They do operate the mixing doors for the heat/ac. They are located under the dash and behind the dash. Not too difficult. Mine had some dirt and lint on them. Just clean and put back in. You can also buy new ones for about $120 each but mine just needed cleaning. I have 94k on the vehicle.

theazz

Forgot to get back to everyone after I cleaned my servos. Yes they were very dirty. Cleaned them and everything works great. No more noise in the dash.

theazz

I really can't do that because I don't know if the problem is your car electronics or my unit. What I will do is take a picture of the unit temporarily plugged into my SC430 and take a picture of it. I will go through all the buttons to make sure they work. That's the best I can do.

Tell me what is your unit currently doing.

theazz

My price is firm at $250 . Well below ebay

The azz

I'm sure this is the correct unit. I connected it in my 03 SC430 and it worked perfect. Turned out it wasn't my control unit that was not functioning but my servos.

theazz

Here is a picture of the unit I have.

Theazz

I have a spare one that I thought I needed but I don't. My part number says 55960-24260. It's a complete unit.

theazz

Static or gurgle sound is back. Apparently others have had this and it's faulty servo's. There are a total of 4 on the sc. Cleaned all 4

(trying this first) . Sure hope this does the trick.

Theazz

I have a 2007 rx350 and need tires. I've done Michelins and now looking at

Continental Pure Contact Eco Plus. ( best seller on tire rack). Want quiet tires. Anyone have an opinion?

Theazz

Looking for an ac-heater control unit (sits above the radio) or just the computer portion. I've seen them for $200 but trying to pay less than that.

theazz

Shawn

I received my cree lamps for my reverse sockets on my sc430. I can't seem to get them to work. I've reversed the polarity (reversing the bulb) but nothing. When I put my original back in it works fine. Did you have any issues when you did yours.

theazz

Luckily I was able to unplug and plug in again and the noise stopped. So I'm thinking just a bad connection at least for now.

Finally found the problem. Decided to dive into this and started to pull fuses to see if it stopped. Found the fuse and started to take things apart from the power source to the last thing in the circuit. Turns out it was a bad connector connection on the back of the AC control unit.

Happy Days

theazz

Shawn

What about the door sill plate bulb. Did you replace it and how did you get it out. I can get the sill plate out but can't see how to get access to the lamp.

theazz

Thanks

Shawn

That's exactly what mine look like. Wish I had the bronze look in both. I've purchased a used passenger side mirror and hopefully the blotchy look will be gone. Also did you see my note to you about the led lamp numbers you used on your interior lights?

The azz

Shawn

Do you have light numbers for your led conversion or did you post that and I missed it.

Thanks

Theazz

No I'm not the original owner. The passenger outside mirror is starting to be blotchy so I want to replace with a used oem off of e-bay.

Is it me or is there 2 different tints to each side mirror. My drivers side is a bronze look and my passenger side is a blue tint

I have a 2007 RX350 and while changing out an ignition coil I pulled out the wires on the camshaft position sensor "B" Bank 1 connector.

I bought a new connector and wire for it. It has 3 wires on the connector. Does anyone have the electrical manual for the 2007 RX to tell me what pin on the connector goes to the harness wires so I can solder them in (a diagram would be great). The harness wires are yellow black and white.

Thanks

Theazz

No really that's got to be a mistake $500 for a 7"x3" mirror?

Need to replace my outside right "mirror only'. Does anyone have a part number for a 2003 SC430

Again just the mirror.

Thanks

theazz

Yes your right its a different engine. Thanks anyway for you help

I have a 2007 RX350 but if you have a diagram for the 400 maybe its in the same place.

Thanks for your reply