nurvcom

i have 01 is300 I need rear view mirror with cover that hides the bolts 1 center cap from stock wheels trunk release cable ( from front to trunk lid ) hood prop with holder that hold it to hood and Tan arm rest (need everything to install in non arm rest is300 ) text me at 865-446-0744 or message me here i need this item

my car is 1993 sc400 and i dont have normal key i only got little stick that u hide away well i got another ecu and my car still wont start this beast killing me no cracking and fuel pump doesn't come on with key if i bypass fuel pump ecu pump works fine with key if i by pass start relay under hood starter wants to crank over stuff i got into it New starter New used ECU (since my had bad caps) Check wiring harness on motor it fine NEw starter relay check all fuses all look good and swapped with new on few for starting stuff just in case tested key switch is sending start signal starter relay is not getting start signal i have no clue where to look... help.... Read more: http://www.clublexus.com/forums/performance-and-maintenance/690948-1993-sc400-problems-2.html#ixzz2TTXd9tGW

1993 sc400 and mine stop running :(

ok so i got this sc400 and wont crank to start new starter new starter relay i bypassed starter relay and starter will crank all fuses good starter relay not getting signal and i have no clue where to look or do

ok my injector is working my plug is wet every time i pulled it out and it got a week spark when car running but when it was running good in am i fire normal and no misfire only when motor heats up it start misfiring when motor is dead cold it runs perfect..

no codes and none stored on ecu today my car started perfectlly and didnt misfire i drove to work and as soon as i pulled in it started misfiring ... no check light do you think cam or crank sensors are going bad .... i was reading that cam or crank sensor can become heat sencitive

both coil new i just replaced them i even tryed putting old on back on still same

ok this morning i got in car car started perfect and didnt misfire till i got to my work i turn off and turn back on and it was misfiring it was after it was heated up would CAM SENSORS be going bad aka heat senstive now making my car misfire.....

yes when i pull each pulg off the motor get worst but on cyl 5 no Change on how motor acts

well changed rotor and caps and car still misfiring for min on way home car stop mis firing and was running perfect and then started agine once i restarted car

update replaced ignitor 1 new wires and check both coils car still misfiring bad cyl 5 still dead i order new cop and rotor ( u guys think this mite help ))

ok well after i was coming back from a work trip 450miles my car started to shake and misfiring so i looked and seen my wires need replacing so new oem installed new plugs installed NGK (driver side coil had a crack I seen so I replaced ) my car is still missing and i tested each plug cyl 5 i can unplug and nothing changes but if i unplug any other plug car get worst what could i look at new and i got code 14 for ignitor 1.... (is ign1 by shock tower or by air box )) Thanks Anthony

ok i got under car and started to take look at the mess of oil pan Dam it going to be fun Any good ideas that could help me fix with out taking motor or anything big out I don't the place to do it :( and could anyone tell me if my ls400 is California or 50 state Model trying my best to get this car to 100% good running and clean car one step at a time ...

ya inside the black cover where the magnet is the bearing was rusted and stopped moving there was a small hair line crack at bottom of the plug on black cover... ok for your part 2

ok pulled IACV it was rusted inside? i never washed Motor :( so i got one from pick n pull it working perfect :) Should i add Motor oil like Stop leak or something near that to oil to help it not smoke After cleaning tbody and could i remove top part of intake manifold to Clean? or is that overboard