Jump to content


Leaderboard

Popular Content

Showing content with the highest reputation since 08/14/2019 in all areas

  1. I was also sold this "invisible" ad on! Only to be told by the dealership "after" that it's not adjustable. So basically it's just a dimly lit thin strip! This should be included. Lexus could and should've done better!
    4 points
  2. Hi. Some friends of mine suggested that I should post this here for more people to see. Hopefully it'll help people for years to come. You will need: About 50 bucks budget for the balljoint rod and the pipe clamp. Height sensor with bracket. 10mm wrench Washers that fit 10mm/M6 bolts. 10mm/M6 nuts Some smaller (8mm wrench) I own a 2001 LS430. The height sensor control arm's slider has rusted and become damaged over the last 19 or so years. The ball joint rod to the height sensor has also seized too. The height adjustment rod there in the red was seized, and the height slider in the blue was badly corroded and broken off. Rather than buy an entire control arm (green) this is an alterative method to repair it The arm is ~26mm in diameter. Buy yourself one of these pipe clamps in 26mm diameter. Or make one. Shouldn't be expensive. The hole needs to fit a M6/10mm bolt. Grind off the remnants of that slider from the control arm, and slide the pipe clamp over, and put your 10mm/M6 bolt and nut through and secure it in place where the slider used to be. Rather than using the control arm as a slider, we can instead use a sliding ball joint rod such as this one; This is a 220 320 00 32 from Mercedes - a height adjustment rod with a 8mm locking and a 10mm/M6 ball joint bolt. You can pick one up off eBay for cheap. Or find some other M6/10mm adjustable ball joint rod. Look at the diagram and try to imagine it in your head. This is what your bracket and rod/clamps should look like. One day I might snap a picture of what my repair looks like, but I hope you can make out what I mean via the diagram. This repair should be very easy. Maybe some sanding/grinding and surface preperation. The clamp will hold on tight and is easy to replace. The adjustable link rod will last longer and allow for easy adjustment, and less risk of corrosion damage. Hope this helps. This is a fairly easy job and took me less than 2 or so hours to do.
    3 points
  3. Did I mention this?..... I don't like the fact that our governments plan to force us to buy EVs. I wouldn't mind having one, as we already have solar panels and don't pay for electricity, but I think we should be able to choose what we drive (within reason).
    3 points
  4. At the part store they run a load test on the battery that mimics a big draw. If it holds up to a certain voltage it means the battery itself is not weakened yet. As the battery ages it will weaken as in not be able to supply a given amount of cold cranking amps. When its cold the oil thickens some thereby making the engine have to work harder to rotate. Hence the term "cold" cranking amps. I'd say you should investigate why the check engine lamp is lighting up. It could be a sign of what is taking place to cause your car to struggle to crank over. The part store can often "read the code" and determine why the CEL is lighting. My gut tells me your voltage regulator in the alternator is hit and miss. A long time ago that was a little box on the fire wall or fender. These days they are inside of the alternator. It determines how much electricity goes to the engine to keep it running and to the battery to charge it. It only has to be off by a little to keep the engine running but not have extra to charge the battery. Another issue could be a parasitic drain. An out of the ordinary draw on the battery when the car isn't running. In my 04 GS 300 for example the CD changer kept trying to change discs and the seat memory kept activating. Now I could not hear the disc changer nor was the seat memory moving the seat, but they were drawing on the system leading to a weak or dead battery if I didn't drive the car every day. Yet another issue may be short trips don't allow the battery to charge enough. Example; start the car, drive to a store 10 minutes away, finish there, start car and drive 10 minutes to another store. Never giving the engine a good 30-45 minutes to charge the battery back up to the voltage used to start the car can also lead to the hard to crank or dead battery issue. Hope you find it soon and it's a cheap and easy fix.
    3 points
  5. No reason to upgrade, Those stock wheels are Classic on the SC 😉
    3 points
  6. But you love the Covid virus? 🙄
    3 points
  7. I just installed the rr racing supercharger. It’s the only way to go bud
    3 points
  8. That one is my son's new puppy. Her brother came home with me Chocolate lab mom, stranger in the night dad Yesterday they played all afternoon.
    3 points
  9. Purchase has been made!...I could not turn down the deal I got & the actual ES...2020 ES 350 'premium' with only 11k miles in Nebula Grey Pearl (windows are already tinted)....over 2 years of full factory warranty remaining; 1 owner, full service history & Lexus CPO. Our 'premium package' in Canada is equipped quite differently than our friends south of the border....with more features / standard equipment. Originally I wanted the UL package....but in these parts, they are very rare (I reached out to 17 Lexus dealers in a 400 mile radius of me...the UL units that are available are 5 to 6 k more & only about 20% are actually at Lexus dealers...the premium pkg checks 95% of the boxes I was looking for....as the expression goes 'don't look a gift horse in the mouth'. I literally have a 6 minute drive to work... I pick the car up this Saturday.
    3 points
  10. I like it when I'm trimming a rose bush, grab one to place in a jar and while heading indoors the Mrs arrives from work so I hand her the rose. Or when I come from work and the dog greets me at the door, tail all wagging-like. And the parrot says "welcome home"…… Or when a nice breeze blows just as the grass cut chore is over and the Mrs brings out a tall glass of ice cold spring water. Or when a new baseball cap fits my noggin just right without adjusting it. Or I step on the bathroom scale expecting to have gained weight but the scale shows I actually lost a little. Or when my son and I went to do the first start after an engine swap, expecting a hard to start issue but ole bessy fires right up. Or when the lawnmover starts first pull……again. Or helping out old people. Or thanking a soldier/veteran. Or tipping the person at the toll booth. Yes I stop and pay in cash so I can do that. Or when the voicemail on your phone was not a robo-call and instead was a friend telling you "hello, here's my new phone number" Or when you sneeze and a perfect stranger says "bless you". Life is short. But smiling makes you live longer. Trouble with being dead is it lasts so long.
    3 points
  11. The cost of dental work, especially deep cleaning by laser and periodontal surgery, but also including implants.
    3 points
  12. That's the view when I pull into the driveway after work. Unseen in the photo is the dog wagging his tail "it's that guy, he's back, yay!!"
    3 points
  13. Update: I think I have got it after all the work, time, and money spent. I started checking again I found an unbelievable vacuum leak around lower intake manifold. replace gasket today runs great thanks for all of the support. something that simple fix. when the engine was swap the starter was replaced. The gasket moved or something apparently cause a vacuum leak. I had no idea a vacuum leak could cause random misfires. I was sure it was an ignition problem.
    3 points
  14. The Lexus brand cell phone that was a dealer installed option lowered the HVAC fan speed and muted the audio system while a call was in progress. I even connected an aftermarket Nokia CARK-91 phone system I installed in my second (2000) LS400 to mute the audio system but I didn't bother to connect it to lower the HVAC fan speed. Even when a Lexus phone system was never installed, corrosion of the factory installed cell phone harness in the trunk can cause HVAC and audio system issues.
    3 points
  15. 20 years ago I swapped a domain name for a Lexus. The love affair started and I am now on my 10th Lexus
    3 points
  16. My Lexus is my weekend car. My daily is my 2009 Mazda 3i.
    3 points
  17. Just acquired a 97 LS400 with 5 keys, second owner, all original paperwork from the dealer including the peel away handbook that came with the car. Have the original window sticker even! Crazy come up from working on the car for a neighbor during the plandemic. Just like to say hi and start helping where I can here, been a tech for over 15 years professionally, 26 cars owned probably more including bikes. Hope to help out and be helped if inrum into some issues here on this new venture. Hope to add an air ride system in the future, tint, visors, etc. Who knows..
    2 points
  18. 2 points
  19. Thanks for the advice it is much appreciated. Now that it has been bleed correctly. I now have power with no leaks.
    2 points
  20. Yes, indeed, John! Jeff, to fully answer your questions: The Continental Pure Contact tires are great, in my opinion. When I drive the RX, I am mostly very conservative, especially now that gas is almost $6/gallon. As with most all-season tires on a heavy vehicle, aggressive cornering will solicit slight squeals from the tires. The advantages of these tires are longer life and quiet/smooth ride.
    2 points
  21. re: 400h Thank you for your reply. I'll have to jack it up and check. I happen to have a new crush washer for the drain bolt. I hope I can use that one.
    2 points
  22. This partially why I gave up riding a motorcycle to focus on convertible sportscars in which I can drive with shorts and a tank top during Summer months.. 😏
    2 points
  23. Back again with photos. Full disclosure, some pulleys and wiring brackets are removed in the photos, you do not need to remove anything that hasn't been mentioned, they're just taken off to have a better line-of-sight for the camera. Installation is the reverse of removal, and everything slides together fairly nicely. 1. You'll start by sliding the alternator onto the stud, letting it hang. Don't slide it back until you've plugged in the connector on the back and slid the rubber boot over top. Next, you can shift it back further and get your charging cable attached. There was not torque spec in the manual (that I could find) but good practice is to tighten the nut for the charging cable until you can't move the cable side to side. Slide the boot over top of the charging cable after it has been secured. If you were able to disconnect the wiring bracket on the alternator, reconnect it. If you cut the tape, peel off the old tape and wrap new tape around the mount and harness. Next, slide in your bottom alternator bolt and hinge your alternator side to side, lightly pushing on the bottom bolt to find the threads. Once you have both the nut and bolt lightly seated, you can torque them both to 29 ft-lbf. This is what you should look like at this step. 2. Re-install your power steering pump. The pump will slide straight back, if you meet resistance, double check that your reservoir isn't caught on the cooling hoses attached to the coolant reservoir, and turn the body of the pump on the stud to make sure the mount isn't colliding with the cylinder head. The bolt holes are a bit tricky to find, but for reference, the top hole of the two is directly beneath the widest portion of the valve cover, pictured here: The lower bolt is tucked a bit further and just slightly towards the rear of the vehicle. Here's a photo of the mounting holes on a spare cylinder head I have on the bench: Once all three fasteners are lightly seated on the power steering pump, go ahead and tighten them up. The torque spec is 29 ft-lbf for the two bolts, and 32 ft-lbf for the nut on the front. Go ahead and secure the three bolts holding your pump reservoir in as well. If you're reading this guide ahead of time, the bolt holes are marked with a red "X". Make sure you don't miss the one hiding underneath the coolant feed line. 3. Re-install your belt and cooling fan/ fan clutch. Attached is a photo of the belt routing (you should also have the same routing diagram attached to your hood). Torque spec for the fan clutch nuts is 16 ft-lbf. When you install your belt, make sure it is sitting in the grooves properly by hand. If it is misaligned, it can jump off when you start the engine and damage components. 4. Install your air ducting and vacuum/vent hoses, and reconnect your battery cable. You'll need to go through and re-set your clock, radio presets, and memory seats, but other than that, your job is (almost) done! 5. Check your charging system Your alternator is installed, but verify your system is working before setting off down the road. With the engine running, you should have about 14 DC volts. Double-checking this now is the best way to keep from immediately getting stranded with a dead battery, and while you're checking it, you can listen for any abnormal sounds from your engine. Torque values: Alternator mounting nut and bolt: 29 ft-lbf Power steering bolts: 29 ft-lbf Power steering nut: 32 ft-lbf Fan clutch nuts: 16 ft-lbf
    2 points
  24. I believe the image below shows the antennae routing for the RX400h.
    2 points
  25. If you fail to timely replace your timing belt and water pump your engine could suffer catastrophic damage. Do it. Do it now. My mechanic charged $475 today for labor to replace the timing belt and water pump on my LS 400 with 174K miles. My AISN brand kit cost $189 from Sumit plus antifreeze and liquid gasket for a total of $300 for parts. The Stealership will rob you blind. I saw that my belt was cracked and my pump’s weep hole was crusty from leaking. It looks like I was a whisker away from shredding my motor. I’m glad I did it now and avoided killing my Lexus.
    2 points
  26. I thought there was a recall concerning this. You should be able to check, here: Lookup Safety Recalls & Service Campaigns (toyota.com)
    2 points
  27. 2 points
  28. USNews claims the Lexus RX provides 18.4 cubic feet of room behind the second-row seats and 56.3 cubic feet with the second row folded down. Unlike the 3-row model which keyesLexus.com shows that for the RX350L, with all rows in an upright position, it has 7.5 cubic feet of cargo room. Folding down the third row increases the SUV's cargo room to 23 cubic feet. Congrats, Mike! If your dealer is like mine - they put your Lexus in a special delivery showroom with lots of lights. Then they bring you in to inspect the 350.
    2 points
  29. The cost of gas and food...Thanks o'biden
    2 points
  30. I think that cap is actually a left over tap for some funky hot water defroster.
    2 points
  31. Welcome to the Lexus Owners Club Events forum section Its been a while since this section has seen the light of day, so thought it was time to revive it now that we have freedom of movement pretty much in most parts of the free-world. Got an event planned or just want to share one you are attending? Feel free to post up any national or local events relating to Lexus or even just events that will host Lexus cars amongst others. (please note: the Moderation Team reserve the right to remove any content that goes against Lexus Owners Club rules at any time)
    2 points
  32. I don't like when I pour cereal into a bowl at midnight and discover the milk went sour. Dratz!!
    2 points
  33. No manual release, Maybe this will help
    2 points
  34. Recently purchased a 2004 SC430 - black with saddle - 157k. Have wanted one since 2002 when I saw one in the showroom. Long story short, I located one in Texas and after speaking with the owner, decided it was a worth making a deal. While waiting for the car to arrive in Colorado, I signed up for Lexus Owners Club and read as much as I could about the strengths and weaknesses of the car. All I can say is LOC is a fantastic resource for any Lexus owner, but I found it particularly valuable for my newly acquired SC. So far, I have replaced front and rear shocks/struts, both upstream O2 sensors, front brakes and rotors. Within the next month I will replace water pump, tensioners and timing belt. (previous owner did it around 95k) All repairs have been done based on recommendations and information obtained from LOC forums. The suggestions for aftermarket parts were invaluable - as were the recommendations for OEM parts. Repairs were accomplished by a local independent Toyota mechanic I have known for awhile. Cosmetically - the car is in very nice condition. It was garaged most of the time and it shows. Bottom line is a HUGE thank you to all the other SC owners for sharing your knowledge and resources on this forum. Thanks to you, I am enjoying the hell out of this car and plan to have it for many years to come. Here's a photo:
    2 points
  35. Insanely fast and frightening to other bike riders when you take off, in silence, from the lights, like Tron on Steroids!
    2 points
  36. I have always been in the Toyota family. The pandemic has made it hard to find the Toyota I wanted and I know Lexus IS the fancier side of Toyota. They are dependable cars and I need something that’s safe and will last a long time. So I am getting my RX 330 tomorrow!
    2 points
  37. Hey bykfixer, thanks for the input. Ken
    2 points
  38. I agree gamalot. I have family who get their bamboo toilet paper delivered cross country via fossil fuel powered truck. As I type this it is highly likely that every room in their house has a light turned on. They come to my house and comment how hot it is in summer or cold it is in winter. They arrive in three compact hybrids instead of one sedan. They live by the ocean and complain the sea is rising. They fertilize their landscaped lawns then complain about plastic straws polluting streams. They moved away from areas run by high tax and spend politicians then vote for high tax and spend politicians in their community. I grew up when air conditioned cars were for the neighbor who had loot. Back then they had little wings you could dial in to circulate air throught the car so the vinyl seats weren't so uncomfy.
    2 points
  39. Hi all, I believe I have posted here before a long time ago with my old LS430 LEX, I now have a 2007 LS460L with 110K on it now. I have owned it for a few years now, since 65K miles, and recently I started having acceleration/hesitation problems. I did alot of research, and didn't find very many good answers. I did have the transmission and engine ECU update flashed, with some improvement, but after that didn't solve the problem, I was convinced it was the cylinder head replacement deal, which was way out of my budget with 5 kids....and I thought it was ridiculous that a flagship sedan would need that kind of serious motor work with just 100K on it. Anyway, my mechanic suggested BG 44K fuel system cleaner, NOT available at places like autozone. He sells it for $28 per can, but I found on Ebay for $16.75 and up with free ship. First and foremost, I ALWAYS used quality, premium gas (Shell V-Power or QT), and Techron additive from time to time, so I was super unconvinced about his recommendation. I had even listed my LS for sale, again, convinced that the motor had cylinder issues after reading blogs about LS460 acceleration issues. Also, for the record, I have NO affiliation with BG or anything like that. THIS STUFF WORKS! It truly fixed my hesitation problems, completely. I am no longer selling the car, and am happy again, as it accelerates like it is supposed to. Feel free to read many other peoples reviews on this stuff, its amazing and really seems to work. After i drove it to wrok (25 miles one way) I thought i felt a difference, by the drive home, I KNEW I felt the difference, after the full tank, i was truly smiling. I have ordered 4 more cans for my other vehicles and boat, and suggested it to my friend with a ISF, my brother with an SC430, and my buddy with a Vette. I guess these LS460 cars are just picky after a while and maybe the injectors get gummed up? I don't pretend to be a mechanic, again this was suggested by my Lexus mechanic, After alot of depressing research with no real answer, just wanted to share my experience with any other LS460 owners, as it is a beautiful car, and I was disappointed in what I was thinking the problems I had. It was the best $17 I have recently spent, and if you are having similar weak/lack of acceleration or hesitation issues, i would say TRY IT for less than $20. I believe you can go to BG's site and find a local dealer, again, not autozone or O'Reilly or anything like that, says professional use only lol. Also, need a funnel, comes in a coke can basically. Just my 2 cents, hoping to help out any other LS460 owners out there depressed about their car, it seems most people just said they'd trade it in and buy a new one, but I'm not that rich :)
    2 points
  40. problem solved after 3 weeks of on and off diagnostic. it was the crank sensor that failed and this was very difficult problem to diagnose because the crank sensor did work " to a degree ". previous owner sold me this car for 1200 with only 89k miles because 4 or 5 shops that she took this ES300 to couldn't figure out the problem including 2 Lexus dealerships and 1 of them even suggested a new/rebuild motor because they thought somehow, the compression loss after engine warm up while running. I've been turning wrench as a master tech since 2001 and never encountered this problem before. not sure as to unique problem, only for Toyota or not but it was hard problem for sure. if you want details of how and what way the sensor failed or any questions about leading up to my findings, let me know.
    2 points
  41. Funny you bring this topic to light...I use them to store parts when I disassemble a watch, Keeps groups of parts separate before cleaning. I also use for small batch paint mixes 🙂
    2 points
  42. I'm sure a lot of us have heard about Matt Farah's legendary million mile Lexus, but have you heard of the 1,400 Mile 2005 Lexus LS430? Well, it's in the Philippines, and probably one of the lowest mileage examples in the world. See it here on my YouTube channel: https://youtu.be/aDijYmBzzhI https://youtu.be/aDijYmBzzhI
    2 points
  43. So it works! Swapped the old tranny back in. Turns out the ECU capacitors were the entire problem! Thank you all for your help and i hope this helps anyone else that has capacitors issues!
    2 points
  44. Have you tried alternating (on/off) the "auto" feature? Does it affect the heat? When was the last time your heating system coil was flushed? There is a temperature control valve also. If you don't want to go to a Lexus dealer, find a good local independent mechanic.
    2 points
  45. I just wanted to share some insights and info about my 91 LS400. I had the hardest time tracking down a gas smell I was getting only once in a while. I would smell gas in the A/C after the car had warmed up, and only after making a few stops. I would come back to the car and it would reek of gas. Looking around under the hood I could never see a leak. Until one day after stopping I immediately opened the hood and really took my time looking around. After a few minutes there it was, not the fuel pressure regulator but on the other rail my "Fuel Pressure Damper". Out of the top it was spurting gas just under a small screw. The weird part is that when the car was running no leaks. From what I could gather when the car was running there was enough pressure in the rail to seal the leak, but as pressure bleeds off (up to 2-5 minutes after shutting off) it would leak. I replaced my Damper and haven't smelled gas since. I also remember hearing of the LS400 having issues with engine fires while the car was stopped. Guess I know how that was happening. Hope this helps someone.
    2 points
  46. 2 points
×
×
  • Create New...

Forums


News


Membership