Leaderboard

Hello Everyone, I know IACV has been a huge topic on the forum and I have found various pictures in the RX forum and ES forum on the idle air control valve (IACV) or as others call it the idle speed control valve (ISC). However, I have not found a "step by step" posting to date which definitively shows how to clean this thing so that my car stops giving me idling problems. Symptoms I have had included: - low and rough idling that would cause the car engine to start shaking after starting the car - this eventually got worse to the point that when I start my car, it would not idle unless I gave it gas - idling problems for me tended to occur more often after my engine was warm or had been sitting in the sun I hope these series of postings help you fellow LOC members out there. You've certainly helped me in the past so here's my two cents at this common problem. Additionally, the instructions I give are the way in which I have cleaned it myself. As you go about and attempt this, you may find better ways to do so. Please add and refine my instructions/terminology as needed. I am not a professional. I've only changed my oil, air filters, and conducted minor maintenance previously. The bottom line is that if you have the right tools, you should be able to do this. This discovery/ cleaning took me about 2 hours to do cause I ran into problems and there were major steps left out in previous postings that I’ve encountered read. The next time I do this, I believe I can get this done in about an hour or less. Tools Needed: 1) Tightly fitting Philips Screw Driver 2) Carb cleaner that is O2 sensor safe (I've seen CRC. I used Valvoline Carb Cleaner) 3) Locking Grip Pliers (definitely helped me remove the factory tight screws) 4) Small brush for cleaning 5) Towels for cleaning 6) Pliers (help removed brackets holding the hoses) 7) Latex gloves helps with limit the messiness. * I used the same gasket and did not replace it. No problems found. 1) Remove the hose that comes from the engine/motor that connects to the air intake hoses.( Hose is below in red – we’ll refer to this as Hose A) When you pull back the rubber hose covering, you will see that a metal bracket is holding the hose pretty tightly in place. Use the pliers to clasps the two metal pieces together to loosen the bracket and pull the hose loose. You can also do this by hand if it’s easier for you. 2) Upon removing the hose, you will want to remove the two air intake hoses. Loosen the three screws above in green and remove the hose. Below is a picture of the intake hoses removed. 3)After removing the intake hoses, I opened the lid to the air filter and moved this to the side of the car to create more working room. I believe there are two clips on the right holding the lid in place. Just pop the two clips and move the cover to the side. I also took out the air filter and temporarily moved this to the side. 4)After removing the intake hose, the throttle body/IACV/black electric coil is revealed. At this point, I removed the black electric wire from the black coil. Once the electric wire is removed you can remove the black coil from the IACV by removing the two screws. Note, the screws are factory tight so use a tight fitting screw driver to remove the screws. One of my screws was partially stripped from the dealership’s work, so I had to resort to my locking grip pliers which helped out tremendously. After removing the two screws, the black electric piece pops right off. When the black electrical coil is removed from the IACV, it exposes a small pencil sized metal stud. You will also notice a washer that sits on this stud. Don’t lose this washer. Take it and put it aside so it doesn’t fall off when you continue on in the next steps. 5)Additionally, I removed the hose coming out of the IACV. We’ll call this Hose B. This hose can be removed in the same manner by clamping the bracket and pulling the hose out. You will see that the hose is removed below. Below are pictures of before and after. 6)Here is where the fun begins. I initially attempted to remove the four screws attached to the IACV at this point, but found that after an hour, this would be nearly impossible to remove considering the location of the screws were in an extremely tight spot. The only way I would be able to remove the IACV is to remove right throttle body. Not as tough as it sounds. Three screws need to be removed to accomplish this. Again, be careful when removing the screws. Also you will see I removed another electric plug and I also cut a tie wrap. Once you complete these steps, the throttle body/ IACV comes out pretty easily. Note when you remove the throttle body, there will be one LAST hose connected to the IACV. Be careful when you remove this hose as radiator fluid may spill. Some of my fluid spilled out so I just refilled my coolant after I was done. 7)Below is a picture of the bottom view of the IACV. You now can EASILY remove the four screws connecting the IACV to the throttle body . In the picture below, I have already removed one of the screws. Once the four screws are removed the IACV and throttle body separate. Now you can clean both of them with your carb cleaner, brush, towels, cotton swabs etc…. Picture here is before I the cleaning with all the muck inside Pictures after I cleaned the IACV and throttle body This last picture is the post throttle body cleaning 8) Once you are done cleaning, just put back the throttle body/iacv the same way you took it off, and put everything back in reverse order. Ensure the gasket is in place. Also, ensure you put the washer back on the electric coil. Make sure you place hose A & B back and ensure the electric plugs are back in their original position. Once these things are in place, then it's all about putting the air filter/hoses back and you are good to go. If you have lost any coolant, make sure you refill it to a safe level. After completing this cleaning, my car starts up without any problem and idles as if I just purchased the car brand new. Replacing this at a dealership would have costed me $300-400 easily. Let me know if you have any questions. Cheers (Also, I tried to post these as separate replys, but the software combined all my replies into a single reply and did not keep them separated) *Edited the posting to have the pictures follow step by step in sequential order*

I was also sold this "invisible" ad on! Only to be told by the dealership "after" that it's not adjustable. So basically it's just a dimly lit thin strip! This should be included. Lexus could and should've done better!

Hi. Some friends of mine suggested that I should post this here for more people to see. Hopefully it'll help people for years to come. You will need: About 50 bucks budget for the balljoint rod and the pipe clamp. Height sensor with bracket. 10mm wrench Washers that fit 10mm/M6 bolts. 10mm/M6 nuts Some smaller (8mm wrench) I own a 2001 LS430. The height sensor control arm's slider has rusted and become damaged over the last 19 or so years. The ball joint rod to the height sensor has also seized too. The height adjustment rod there in the red was seized, and the height slider in the blue was badly corroded and broken off. Rather than buy an entire control arm (green) this is an alterative method to repair it The arm is ~26mm in diameter. Buy yourself one of these pipe clamps in 26mm diameter. Or make one. Shouldn't be expensive. The hole needs to fit a M6/10mm bolt. Grind off the remnants of that slider from the control arm, and slide the pipe clamp over, and put your 10mm/M6 bolt and nut through and secure it in place where the slider used to be. Rather than using the control arm as a slider, we can instead use a sliding ball joint rod such as this one; This is a 220 320 00 32 from Mercedes - a height adjustment rod with a 8mm locking and a 10mm/M6 ball joint bolt. You can pick one up off eBay for cheap. Or find some other M6/10mm adjustable ball joint rod. Look at the diagram and try to imagine it in your head. This is what your bracket and rod/clamps should look like. One day I might snap a picture of what my repair looks like, but I hope you can make out what I mean via the diagram. This repair should be very easy. Maybe some sanding/grinding and surface preperation. The clamp will hold on tight and is easy to replace. The adjustable link rod will last longer and allow for easy adjustment, and less risk of corrosion damage. Hope this helps. This is a fairly easy job and took me less than 2 or so hours to do.

Did I mention this?..... I don't like the fact that our governments plan to force us to buy EVs. I wouldn't mind having one, as we already have solar panels and don't pay for electricity, but I think we should be able to choose what we drive (within reason).

At the part store they run a load test on the battery that mimics a big draw. If it holds up to a certain voltage it means the battery itself is not weakened yet. As the battery ages it will weaken as in not be able to supply a given amount of cold cranking amps. When its cold the oil thickens some thereby making the engine have to work harder to rotate. Hence the term "cold" cranking amps. I'd say you should investigate why the check engine lamp is lighting up. It could be a sign of what is taking place to cause your car to struggle to crank over. The part store can often "read the code" and determine why the CEL is lighting. My gut tells me your voltage regulator in the alternator is hit and miss. A long time ago that was a little box on the fire wall or fender. These days they are inside of the alternator. It determines how much electricity goes to the engine to keep it running and to the battery to charge it. It only has to be off by a little to keep the engine running but not have extra to charge the battery. Another issue could be a parasitic drain. An out of the ordinary draw on the battery when the car isn't running. In my 04 GS 300 for example the CD changer kept trying to change discs and the seat memory kept activating. Now I could not hear the disc changer nor was the seat memory moving the seat, but they were drawing on the system leading to a weak or dead battery if I didn't drive the car every day. Yet another issue may be short trips don't allow the battery to charge enough. Example; start the car, drive to a store 10 minutes away, finish there, start car and drive 10 minutes to another store. Never giving the engine a good 30-45 minutes to charge the battery back up to the voltage used to start the car can also lead to the hard to crank or dead battery issue. Hope you find it soon and it's a cheap and easy fix.

I just purchased a NX200T. During the test drive I did not realize the headrest was a little too far forward. It is sharply angled toward the driver at the top. I am on the shorter side at 5' 6 1/2" tall and have good posture. When I sit in the driver seat with good posture my head is pushed forward about 1/2". I have to lean the seat back so I am slouching to avoid neck discomfort. I asked my dealer, service center and the U.S. corporate office for advice. There was nothing they could do. Very disappointing. The worst part is that the headrest is available outside the US with adjustable forward and aft movement at 4 intervals. I asked a few after market car parts dealers for advice. I was told it is a common problem. I was given many solutions (get another brand car's headrest, cushions, heat the metal and bend the rods, padding, etc.). Some ideas were unsafe and of course illegal I thought. For now I put some 2" cushioning in the seat to bring the rest of the seat inline with the headrest. It is better but not quite there and makes my A/C venting fairly useless, & is a little dorky. After just having paid about 50K for the fully loaded car I want a professional solution to improve the headrest. So far I have not solved it. I am curious if anyone else has had this issue and solved it? Any advice is appreciated. I am 95% happy with the car/SUV and am looking for that last 5% of comfort/fit.

No reason to upgrade, Those stock wheels are Classic on the SC 😉

But you love the Covid virus? 🙄

I just installed the rr racing supercharger. It’s the only way to go bud

That one is my son's new puppy. Her brother came home with me Chocolate lab mom, stranger in the night dad Yesterday they played all afternoon.

Purchase has been made!...I could not turn down the deal I got & the actual ES...2020 ES 350 'premium' with only 11k miles in Nebula Grey Pearl (windows are already tinted)....over 2 years of full factory warranty remaining; 1 owner, full service history & Lexus CPO. Our 'premium package' in Canada is equipped quite differently than our friends south of the border....with more features / standard equipment. Originally I wanted the UL package....but in these parts, they are very rare (I reached out to 17 Lexus dealers in a 400 mile radius of me...the UL units that are available are 5 to 6 k more & only about 20% are actually at Lexus dealers...the premium pkg checks 95% of the boxes I was looking for....as the expression goes 'don't look a gift horse in the mouth'. I literally have a 6 minute drive to work... I pick the car up this Saturday.

I like it when I'm trimming a rose bush, grab one to place in a jar and while heading indoors the Mrs arrives from work so I hand her the rose. Or when I come from work and the dog greets me at the door, tail all wagging-like. And the parrot says "welcome home"…… Or when a nice breeze blows just as the grass cut chore is over and the Mrs brings out a tall glass of ice cold spring water. Or when a new baseball cap fits my noggin just right without adjusting it. Or I step on the bathroom scale expecting to have gained weight but the scale shows I actually lost a little. Or when my son and I went to do the first start after an engine swap, expecting a hard to start issue but ole bessy fires right up. Or when the lawnmover starts first pull……again. Or helping out old people. Or thanking a soldier/veteran. Or tipping the person at the toll booth. Yes I stop and pay in cash so I can do that. Or when the voicemail on your phone was not a robo-call and instead was a friend telling you "hello, here's my new phone number" Or when you sneeze and a perfect stranger says "bless you". Life is short. But smiling makes you live longer. Trouble with being dead is it lasts so long.

The cost of dental work, especially deep cleaning by laser and periodontal surgery, but also including implants.

That's the view when I pull into the driveway after work. Unseen in the photo is the dog wagging his tail "it's that guy, he's back, yay!!"

Update: I think I have got it after all the work, time, and money spent. I started checking again I found an unbelievable vacuum leak around lower intake manifold. replace gasket today runs great thanks for all of the support. something that simple fix. when the engine was swap the starter was replaced. The gasket moved or something apparently cause a vacuum leak. I had no idea a vacuum leak could cause random misfires. I was sure it was an ignition problem.

Hi all, I believe I have posted here before a long time ago with my old LS430 LEX, I now have a 2007 LS460L with 110K on it now. I have owned it for a few years now, since 65K miles, and recently I started having acceleration/hesitation problems. I did alot of research, and didn't find very many good answers. I did have the transmission and engine ECU update flashed, with some improvement, but after that didn't solve the problem, I was convinced it was the cylinder head replacement deal, which was way out of my budget with 5 kids....and I thought it was ridiculous that a flagship sedan would need that kind of serious motor work with just 100K on it. Anyway, my mechanic suggested BG 44K fuel system cleaner, NOT available at places like autozone. He sells it for $28 per can, but I found on Ebay for $16.75 and up with free ship. First and foremost, I ALWAYS used quality, premium gas (Shell V-Power or QT), and Techron additive from time to time, so I was super unconvinced about his recommendation. I had even listed my LS for sale, again, convinced that the motor had cylinder issues after reading blogs about LS460 acceleration issues. Also, for the record, I have NO affiliation with BG or anything like that. THIS STUFF WORKS! It truly fixed my hesitation problems, completely. I am no longer selling the car, and am happy again, as it accelerates like it is supposed to. Feel free to read many other peoples reviews on this stuff, its amazing and really seems to work. After i drove it to wrok (25 miles one way) I thought i felt a difference, by the drive home, I KNEW I felt the difference, after the full tank, i was truly smiling. I have ordered 4 more cans for my other vehicles and boat, and suggested it to my friend with a ISF, my brother with an SC430, and my buddy with a Vette. I guess these LS460 cars are just picky after a while and maybe the injectors get gummed up? I don't pretend to be a mechanic, again this was suggested by my Lexus mechanic, After alot of depressing research with no real answer, just wanted to share my experience with any other LS460 owners, as it is a beautiful car, and I was disappointed in what I was thinking the problems I had. It was the best $17 I have recently spent, and if you are having similar weak/lack of acceleration or hesitation issues, i would say TRY IT for less than $20. I believe you can go to BG's site and find a local dealer, again, not autozone or O'Reilly or anything like that, says professional use only lol. Also, need a funnel, comes in a coke can basically. Just my 2 cents, hoping to help out any other LS460 owners out there depressed about their car, it seems most people just said they'd trade it in and buy a new one, but I'm not that rich :)

My Daily 😀

The Lexus brand cell phone that was a dealer installed option lowered the HVAC fan speed and muted the audio system while a call was in progress. I even connected an aftermarket Nokia CARK-91 phone system I installed in my second (2000) LS400 to mute the audio system but I didn't bother to connect it to lower the HVAC fan speed. Even when a Lexus phone system was never installed, corrosion of the factory installed cell phone harness in the trunk can cause HVAC and audio system issues.

20 years ago I swapped a domain name for a Lexus. The love affair started and I am now on my 10th Lexus

And Because We All Love Pictures 🙂

My Lexus is my weekend car. My daily is my 2009 Mazda 3i.

Here are a couple of tips I have picked up regarding maximizing fuel efficiency 1. Replace the spark plugs if you have not already, I prefer NGK Iridium plugs 2. Look for Cooper CS5 Grand Touring/Ultimate Touring tires, they are excellent for these cars 3. Use OVERDRIVE on the highway or at speeds in excess of 60 MPH (most say 40-50 MPH, but in my car I have observed minimal difference at those speeds). Note that you can use Overdrive at all speeds and it will keep the RPM's down but from what I have learned at slower speeds this translates to negligible fuel economy gains. 4. Set your ECT mode to NORMAL and not PWR 5. Keep the RPM's as low as possible aka don't floor it 6. Make sure your wheels are balanced and aligned properly and that your tires are also correctly inflated. 7. Mythbusters proved this, KEEP YOUR CAR CLEAN, it does SLIGHTLY affect gas mileage for the positive. 8. Turn off your A/C system if you want, it does affect gas mileage slightly, but its also a comfort, not really necessary unless you want to maximize fuel economy. 9. In reference to replacing the spark plugs, you may also want to consider replacing the ignition coil, distributor cap & rotor, and plug wires if they have not been replaced in quite some time as they can lose spark and cause poor performance, this would be within a general tune-up. 10. Replace the fuel filter, this is commonly missed on every car, and they get NASTY, unclean fuel = bad performance. Also consider getting a professional fuel service done on your car, this can help too, especially if it has not been done in some time.

Folks, and Forum Admin, Please make a separate section on the Forum for 2016 RX models. THese have had major changes since 2015. The engine has been tweaked, there are scores of safety improvements and the look is way different. I am sure the issues will be different as well. So please rename the 2010-Present section to say 2010-2015 and keep it separate from 2016 onwards. Thanks.

I can answer that. Those zany Brits particularly like "mark" designations: https://en.wikipedia.org/wiki/Mark_(designation Maybe it is a longing for Jaguar sedan series names. In the UK, the model year ranges of the LS400 are referenced thusly: Series 1, Mark 1 = 1990-1992 Series 1, Mark 2 = 1993-1994 Series 2, Mark 3 = 1995-1997 Series 2, Mark 4 = 1998-2000

Replaced the Y pipe. Almost one month and no more problems.

okay guys, I am going to give you a very constructive advice on how to fix this problem.first remove the cluster and if you do not know how go to lexls.com and follow the instructions.then remove the face cover .first grap the tach needle gently and pull untill you hear a pop,again be gentle and do not ge scared.once you hear the pop move the needle clockwise untill it pops again then gently release it.now move the needle slowly counterclock till you sit it over the zero an on the dot and make sure that it sits right on the zero.to check your work move it gently say to the mark 3 then let go it should snap right back to zero,once you have accomplished this ,you are rock & roll baby.the same thing goes for speedometer.back light is not working change cap 212,after making sure your cathodes are okay meaning the bulbs.if not you can get them at a very good price from plano lexus,they are awsome as far as price goes.gas guage slow change cap 142.while you are at it change any bad or weak bulbs ,be the warning ones or the indicator ones such as shifter position.by the way guys the cluster lexus has on the first gen is the 1992,because the psb are so robust,where the 1993 and 1994 are made a little bit on the cheapy side.this job should take about an hour if you how to handle things.good luck and let me know. please make a donation to lexls.com,this guy is great.may god bless his soul.

Typically, a flashing CEL means that engine damage is eminent (usually catalytic converter damage). In your case, probably due to overly rich mixture or misfires. Perhaps the plug wire repair was temporary? As far as no communication with a scan tool, read here. Not saying this is the problem but it should be towards the top of the "should be considered" list: https://www.clublexus.com/forums/ls-1st-and-2nd-gen-1990-2000/656360-all-my-crazy-lexus-issues-solved-ecu-leaking-capacitor.html Of particular interest from link: MODELS/ENGINES AFFECTED: This issue affects all Lexus & Toyota models with the following engines: 1JZ, 2JZ, 1KZ, 1UZ, 5E, 1G, 3S The following are some of the models affected: ● Lexus LS400 - 1990-2000 (in 1997 and earlier models, the problem is extremely common) ● Lexus SC300 - 1993-2000 ● Lexus SC400 - 1992-2000 ● Lexus GS300 - 1993-1996 ● Toyota Celica GT - 1985 -1998 ● Toyota Supra Mark III (JDM) - 1986-1993 ● Toyota Supra GT - 1995-1997 ● Toyota Supra Mark IV - 1993-2002 ● Toyota Supra Twin Turbo - 1993-2002 ● Toyota MR2 - 1990-1999 ● Toyota Camry - 1987-2001 ● Toyota Soarer - 1992-2000 ● Toyota Aristo - 1993-1996 ● Toyota Celsior - 1990-2000 SYMPTOMS: Please understand that any one of these symptoms can be a sign of ECU capacitors beginning to fail. - You do not need all or most of them to have this issue! Your ECU capacitors are strongly suspected if you have at least one of the following intermittent issues on your Lexus or Toyota: ● problems in getting into diagnostic mode or scanner says "no communication" ● random dropping into "limp home" mode ● weird shifting problems ● OBD port is unresponsive, seems dead ● throwing random fault codes ● engine won't rev out/rev limits at 2000 or less rpm ● engine runs like crap, then suddenly runs fine again ● random not starting or cutting out ● low idle or erratic idle ● often very hard to start, requires starting fluid ● transmission will not automatically shift, only manual shift is possible ● transmission jerks from 1st to 2nd gear, and kinda slips from 2nd to 3rd ● no A/C compressor operation ● idle speed rolling up and down, or sometimes too low and sometimes too high ● speedometer not working reliably ● speed (cruise) control not working ● tachometer not working sometimes ● air bag light flickering intermittently ● A/C going into reset with flashing front defog light (front defog light typically flashing 10 times) ● check engine light on sometimes, but no codes stored, often in concert with ECT light ● ECU not communicating with scanners or not displaying codes with jumper installed ● bad sulfur exhaust smell in concert with not running right above

It's cheap in the view of things. I don't want to have to replace this motor. I shopped for 9 month before buying my SC430. I have done maintenance that it turned out had already been done. I'm not going to call the prior owner with these types of questions. I save those calls for important stuff. So I did all the fluids a week ago. engine oil it was due and I knew it from the miles I had put on. Transmission fluid was perfect when I dropped the pan, no burnt smell, no metal on the magnets in the pan. Cleaned it all anyway, changed the filter and gasket and added 6 quarts back in. But perfect fluid should have been my clue that it had been done. LOL Get back to the differential, and you guessed it, dumped out perfectly clear, like new gear oil. Let it drain anyway and refilled with 2 quarts. I think most people with these cars keep the maintenance tip top. That is a plus in my book. I intend to keep this car so I like knowing where it stands maintenance wise. Yes it costs a little money but I do believe it helps the cars last. And that's why I picked a Lexus and not a Mercedes or other cars of this type of styling. If you want to gamble on maintenance there are plenty of other models of Lexus cars or others out there to do that with. But I bought this car because it's becoming a classic and its got the Toyota drive train. I plan to keep the car the rest of my life and enjoy it for all that time.

re: 400h Thank you for your reply. I'll have to jack it up and check. I happen to have a new crush washer for the drain bolt. I hope I can use that one.

This partially why I gave up riding a motorcycle to focus on convertible sportscars in which I can drive with shorts and a tank top during Summer months.. 😏

I thought there was a recall concerning this. You should be able to check, here: Lookup Safety Recalls & Service Campaigns (toyota.com)

I'm not sure tbh. I didn't look that close. I did find where it plugged in, and the engine seems to be running fine. So I'm choosing to assume I guessed and got lucky.

OK, All looks good now...Thanks a Mint ^^^

Generally, this sort of info isn't going to had just from vin#. The build sheet is where this would likely be found. Not sure how easy it would be to get on a 7+ yr. old car. Good luck.

My God, how old are you, 90?😏

I don't like when I pour cereal into a bowl at midnight and discover the milk went sour. Dratz!!

...talk about waiting until the last minute!😏

I had always admired the Lexus way. You start out with a super reliable brand of automobile and add top of the line features that folks who don't need to ask "how much does it cost" go for and add sexy looks and you've got yourself a winner. Now for a guy like me who does have to ask "how much" the resale value held so well that they stayed beyond my price range for a long time. Long enough to forget about it actually. But my son bought a GS300 to turn into a left hand drive Aristo. First time I saw it I commented how that is one fine old car. Old I say because it was almost old enough to vote in the US. When he found a genuine Aristo in great shape for less than the cost to retrofit his GS he decided to sell it. All the kids wanted to low ball him or pay him $50 a month. The US gubment sent me a covid check and I figure my son is paying for it anyway so I signed it over to him and he in turn signed over the GS to me. Now it's got some goblins and gremlins but at 18 it's still a dam fine automobile. Will it be my last Lexus or first Lexus? Time will tell on that front. That largely depends on how quickly the money pit gets dug I suppose, because even though they hold up well, when things go bad the costs can pile up pretty quickly.

I was tired of looking at the yellow, hazy headlights, so I decided to do something about them today...

There are to many things about my Lexus to fit into just a few sentences I'm a big fan of the review camera and the rear sensors for cars for are about to come across your path as your begin to back up. The quiet ride and oh so smooth ride are excellent. must have add nos. Another feature that is a must have. is the blind spot mirror. It has saved me from an accident more than once. Paul

I lost my in house mechanic (Jon) due to health problems, but allowed Candrell Car Care to renew my LS at 200,000, by replaceing my Timing Belt/Water Pump, seals, bearings, engine & tranny mounts, plugs seals & VC gaskets and they done a super good job for me.. I have known Bob for about 30+ years, (being in the same business my self) and I already trusted him, but did not know his knowledge of Lexus'es... they are in Carrollton on Midway rd, so if you are in the DFW area, you can trust them.. thanks, billy d powell ..

Just posted this the other day, and now I can't find it, so sorry for the repeat if it is posted elsewhere. I have a 2011 ES350 with 215/55 17 tires. Those are the only size tires the car can come with. I would like to go with a bigger tire to improve handling. To get the same diameter, I would need a 235/50 17, or a 235/45 18. Please let me know if going from the 215 stock tire to the 235 will fit properly on the ES350. I wouldn't think it would be a problem, but I am not sure sonce the factory does not offer a tire size option. Thanks all.

There are at least four versions of the rear seat armrest. Here are two photos: 1. The rear seat armrest of the series 4 Japanese market Toyota Celsior "C type" with audio and HVAC controls and electrically adjustable rear seat with massage. 2. The rear seat armrest of the series 4 LS400 sold in Australia which has controls for the audio and HVAC systems.

My '07 came with the NAV system, and personally I would not waste the time trying to install one. My NAV is vague, and difficult to use in almost all aspects, and it is working "properly". The separate manual for it is about 1/2 " thick, and reading it would also be a waste of time, when you could plug in a Garmin , Tom Tom, or other GPS unit and have it operating in just a few seconds. I did enlist the assistance of a Lexus tech which helped with the shortcuts, but the system is still as I stated previously. In his words Lexus builds fine cars, not fine NAV systems. I guess my point is even if you are looking at plug & play, prepare to be somewhat disappointed. Good luck.

I "think" that the VAIS SL3B will provide A2DP audio streaming on your 2005 SC430: http://www.vaistech.com/site/sl3b.php There may be other companies that have products that will work but VAIS has been around time and their products were commonly offered by Lexus dealers before Lexus vehicles came with similar interfaces from the factory. I suggest that you contact VAIS and inquire before you buy. They may have other products that would be more appropriate for you.

I have had no luck with my dealer on remedying the paint peeling issue. The deal continues to place liability upon Lexus since the vehicle is out of warranty. The dealer ignores the fact that I had brought the paint chipping and peeling issue to their attention on at three occasions while the vehicle was under warranty. The dealer would simply use some touch up paint and offer nothing further. I made claim for a recall with Lexus a couple years ago. The response I received was that my vehicle was an isolated instance and did not warrant a recall. If enough dissatisfied consumers articulate this issue, I am hopeful Lexus will be forthcoming and offer customer satisfaction. Thanks so much for the forum to air this issue.

Hey Jeff, Ditto on the headrest. I'm 'bout 6'3" and told my sales guy I was shaped like a comma in the seat. Not very comfortable. He said the headrest protects against whiplash. True, but not a good answer. I do like the idea about looking for a non-US replacement. Sorry I could not bring anything worth while to the discussion.

Okay, So I just finished my Left rear door. Took much longer than anticipated but I tried to make it as simple as possible and I'm sure I did. I attached the rod onto a circular positive terminal type of socket (it was small, not the type you use on cars). Then I attached that onto the thumb driven lock. It turned out fantastic, the longest part was mounting the damn actuator cause it was in a terrible place, but it came out fantastic. I think the way that I did is the easiest I've seen, well at least for the Rear door. I'd also like to give a special thanks to everyone ont his forum and the other lexus owners forum that helped me do this, and save a whole lot of money.

It works on the 08 IS 350. I just did it. 1) open the car door, get in and close the door, pull the seat belt around and hold it without clicking it home. 2) hit the start button twice with foot off the brake. 3) right away depress the odometer reset button and hold for 10-30 seconds. 4) click home the seat belt. the on off toggle thing comes up on the odometer. select off. wait for the odometer to set. turn the car off.