SRX Posted November 29, 2011 Share Posted November 29, 2011 Is anyone aware of after market no-drill front license plate holders for a 2011 RX 450h? I have seen excellent holders designed for Mustangs from Craig's custom Mustang brackets at jltperformance.com and at a You tube video at http://www.youtube.com/watch?v=El9loVVIeck; the holders are made of stainless steel and attach with stainless steel wing nuts with the plastic bumper fascia of the vehicle sandwiched between two pieces of metal. I did locate one holder requiring drilling holes in the underneath part of the front bumper fascia rather than the front, but would prefer not to drill any holes. Any suggestions are appreciated. Quote Link to comment Share on other sites More sharing options...
pj8708 Posted November 29, 2011 Share Posted November 29, 2011 Is anyone aware of after market no-drill front license plate holders for a 2011 RX 450h? I have seen excellent holders designed for Mustangs from Craig's custom Mustang brackets at jltperformance.com and at a You tube video at http://www.youtube.com/watch?v=El9loVVIeck; the holders are made of stainless steel and attach with stainless steel wing nuts with the plastic bumper fascia of the vehicle sandwiched between two pieces of metal. I did locate one holder requiring drilling holes in the underneath part of the front bumper fascia rather than the front, but would prefer not to drill any holes. Any suggestions are appreciated. http://skenedesign.com/FPBracket/index.shtml ??? I found this, but you may have already looked at it. Paul Quote Link to comment Share on other sites More sharing options...
SRX Posted November 29, 2011 Author Share Posted November 29, 2011 Is anyone aware of after market no-drill front license plate holders for a 2011 RX 450h? I have seen excellent holders designed for Mustangs from Craig's custom Mustang brackets at jltperformance.com and at a You tube video at http://www.youtube.com/watch?v=El9loVVIeck; the holders are made of stainless steel and attach with stainless steel wing nuts with the plastic bumper fascia of the vehicle sandwiched between two pieces of metal. I did locate one holder requiring drilling holes in the underneath part of the front bumper fascia rather than the front, but would prefer not to drill any holes. Any suggestions are appreciated. http://skenedesign.com/FPBracket/index.shtml ??? I found this, but you may have already looked at it. Paul Thanks Paul. I found that site too. This design requires drilling two holes on the bottom lip of the bumper which I was hoping to avoid. Also, do not believe there is the minimum space required to attach the bracket. Did find a gominigo.com site which shows a picture of a non drill bracket on an RX350 that fits in the tow bolt hole and mounts the plate off center. An interesting look. Cost is $85.00 plus shipping which is more than I hoped to spend to put a front plate on the vehicle. Quote Link to comment Share on other sites More sharing options...
pj8708 Posted November 29, 2011 Share Posted November 29, 2011 Is anyone aware of after market no-drill front license plate holders for a 2011 RX 450h? I have seen excellent holders designed for Mustangs from Craig's custom Mustang brackets at jltperformance.com and at a You tube video at http://www.youtube.com/watch?v=El9loVVIeck; the holders are made of stainless steel and attach with stainless steel wing nuts with the plastic bumper fascia of the vehicle sandwiched between two pieces of metal. I did locate one holder requiring drilling holes in the underneath part of the front bumper fascia rather than the front, but would prefer not to drill any holes. Any suggestions are appreciated. http://skenedesign.com/FPBracket/index.shtml ??? I found this, but you may have already looked at it. Paul Thanks Paul. I found that site too. This design requires drilling two holes on the bottom lip of the bumper which I was hoping to avoid. Also, do not believe there is the minimum space required to attach the bracket. Did find a gominigo.com site which shows a picture of a non drill bracket on an RX350 that fits in the tow bolt hole and mounts the plate off center. An interesting look. Cost is $85.00 plus shipping which is more than I hoped to spend to put a front plate on the vehicle. That is pretty pricey...but look at it this way, this is why God made Duct Tape!! LOL Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.