Jump to content

Diy Led Turn Signal Mirror Cover


Halim

Recommended Posts

Last Sunday I finished Led turn signal mirror covers. Red circle is flasher. Blue circle (Green wire with black tracer) is left turn signal output. Yellow circle (Green wire with a yellow tracer) is right turn output. You need to connect those for positive wires of L/R Led mirror cover.

post-72408-0-63057300-1306474815_thumb.j

Link to comment
Share on other sites

Flasher located next right to the interior fuse box driver side.

This flasher located under the steering near the fuse box to the right side. You need to pry the plastic trim under the steering by removing 2 nuts (10mm) lower left and right ( this one hide with small plastic trim need to open by flat screw driver. There is another iron cover need to remove by 2 (10mm) screw on left and right side also. Use heavy cotton gloves, lower side of the cover is very sharp. Then you will see the flasher. Red arrow is the iron cover.

post-72408-0-20333900-1306475120_thumb.j

Link to comment
Share on other sites

Right turn signal connected. I will show you how I connected with right turn led signal cover. Red circle is extra fuse connected with flasher wire (green with yellow tracer).

post-72408-0-39467000-1306475319_thumb.j

Link to comment
Share on other sites

I removed the U shape wood trim ( pry from the bottom to up) by the radio/ac and run this wire behind the glove box to the right side. This mirror glass need to pry from the bottom to up by red arrows using two hands.

post-72408-0-80280200-1306475505_thumb.j

Link to comment
Share on other sites

Removing mirror from the doorRemove this mirror holder cover. See those 3 (10mm) bolts holding mirror. Remove those. PICS: 1 & 2.PICs 3 & 4 mirror removed.

post-72408-0-33313300-1306476526_thumb.j

post-72408-0-20330100-1306476543_thumb.j

post-72408-0-69324800-1306476554_thumb.j

post-72408-0-54668000-1306476574_thumb.j

Link to comment
Share on other sites

Arrow marked plastic cover need to pull out. Follow pics 1. Remove those kind of three screws (red circle) pic 3. Remove (blue circled) three screws also pic 4. Finaly you see this after removed six screws pic 6.

post-72408-0-12446400-1306477134_thumb.j

post-72408-0-37286800-1306477143_thumb.j

post-72408-0-95574800-1306477156_thumb.j

post-72408-0-11120000-1306477176_thumb.j

post-72408-0-83941400-1306477177_thumb.j

post-72408-0-71683400-1306477179_thumb.j

Link to comment
Share on other sites

LED mirror cover. You need this red and black wire run by mirror power cable to the door (pic 1).

Run this wire by the hanger (pic 3 & 4).

Finaly you see this (pic 5)

post-72408-0-09397200-1306477715_thumb.j

post-72408-0-83733500-1306477716_thumb.j

post-72408-0-57168000-1306477718_thumb.j

post-72408-0-36288400-1306477720_thumb.j

post-72408-0-10070400-1306477722_thumb.j

Link to comment
Share on other sites

Drill old mirror cover.Our RX 300 has no extra mirror cover. So drill your old cover almost same size of led wire at the left side.(see pics) Solder the wire connections and taped. Remove the led mirror cover 3m tape and sit on the top of old cover nice and smoothly. Install the mirror glass back by soft press with towel on the white plastic frame.(see pics)

post-72408-0-60213900-1306478071_thumb.j

post-72408-0-80070600-1306478073_thumb.j

post-72408-0-26069500-1306478075_thumb.j

Link to comment
Share on other sites

Run wire through door cable insulator to door.

Behind the glove box locate the flasher connected red wire (which already run) and run through the door cable insulator at the right with black ground wire to the door. I use a body trim bolts as a ground and works. (see pics) Remove the speaker before you run the wire to the door. It will make easy and I used a hanger for run the wire. Here you will see the ground wire and speaker.

post-72408-0-66015900-1306478395_thumb.j

post-72408-0-28563000-1306478397_thumb.j

post-72408-0-70675900-1306478398_thumb.j

post-72408-0-30781500-1306478400_thumb.j

Link to comment
Share on other sites

Final stage.Now bolt the mirror same position with three (10mm) bolts. Connect the blue plug with the harnesse and solder the led wires with flasher and ground wires. Attached the blue plastic and door cover. You done. (see pics)

post-72408-0-11890500-1306478797_thumb.j

post-72408-0-92553300-1306478798_thumb.j

Link to comment
Share on other sites

WOW! Thanks for posting these pictures, i don't believe anyone else has posted a "how-to" for this modification. I think i'm gonna add some LED mirrors on my RX400h, so hopefully it'll work the same way!

Link to comment
Share on other sites

Halim, that is an absolutely excellent tutorial. Maybe you will have to do another tutorial about that Parrot phone kit you installed in your RX! ... couldn't resist saying that.

Really, that was an excellent job.

Link to comment
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



×
×
  • Create New...

Forums


News


Membership